Odd characters? Click here for help. A version of this specification with the linedraw characters approximated by text is available by clicking here.

                         SEAGATE TECHNOLOGY, INC.
                              1-800-SEAGATE
                          http://www.seagate.com
                            (C)opyright 1991



ST-1162A (94354-160) Swift AT (IDE)
     ΪΔΔΔ\
     ³ O ³  5
     ³ O ³  G                                          ΪΔΏ  Some have
     ³ O ³  G       AT (IDE) Cable                     ³ ΓΔ these pins
     ³ O ³ 12  1Ϊ........................Ώ   o o o o o(o o)  6 off
     ΐΔΔΔ/       ........................    o o o o o(o o)  7 off
    ΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝ
                                             1 2 3 4 5 6 7
         ON                 OFF              ³ ³ ³ ³ ³ ΐΒΩ
    1   Slave              Master          ΔΔΩ ³ ³ ³ ³  ³
    2   5 Heads            7/9 Heads       ΔΔΔΔΩ ³ ³ ³  ³
    3   Slave installed    Slave not inst. ΔΔΔΔΔΔΩ ³ ³  ³
    4   7 byte ECC         4 byte ECC      ΔΔΔΔΔΔΔΔΩ ³  ³
    5   Factory test       Normal Oper.    ΔΔΔΔΔΔΔΔΔΔΩ  ³
    6/7 Some PWA's have these pins, factory use  ΔΔΔΔΔΔΔΩ


                             ST-1162A
                          94354-160 Swift

       UNFORMATTED CAPACITY (MB) ________________162
       FORMATTED CAPACITY (29 SECTORS) (MB) _____143
       ACTUATOR TYPE ____________________________VOICE COIL
       TRACKS ___________________________________9,648
       CYLINDERS ________________________________1,072
       HEADS ____________________________________9
       DISCS ____________________________________5
       MEDIA TYPE _______________________________THIN FILM
       RECORDING METHOD _________________________RLL
       TRANSFER RATE (mbytes/sec) _______________1
       SPINDLE SPEED (RPM) ______________________3,600
       BUFFER ___________________________________32 or 64 Kbyte
         Read Look-Ahead, Non-Adaptive,
         Single-Segmented
       INTERFACE ________________________________AT BUS
       TPI (TRACKS PER INCH) ____________________1,350
       BPI (BITS PER INCH) ______________________22,638
       AVERAGE ACCESS (ms) ______________________15
       SINGLE TRACK SEEK (ms) ___________________4
       MTBF (power-on hours) ____________________150,000
       POWER REQUIREMENTS: +12V START-UP (amps) _2.5
                           +12V TYPICAL (amps) __0.7
                           +5V START-UP (amps) __0.75
                           +5V TYPICAL (amps) ___0.4
                           TYPICAL (watts) ______11
                           MAXIMUM (watts) ______33.75
       BUFFERED STEP PULSE RATE (micro sec) _____6-200
       WRITE PRECOMP (cyl) ______________________N/A
       REDUCED WRITE CURRENT (cyl) ______________N/A
       LANDING ZONE (cyl) _______________________AUTO PARK
       IBM AT DRIVE TYPE ________________________*

 * MAY REQUIRE FORMATTING AND PARTITIONING SOFTWARE.  ALSO, CHECK TO
SEE IF YOUR CMOS SETUP HAS A "CUSTOM" OR "USER DEFINABLE" DRIVE TYPE
AVAILABLE.

Possible translation:  804 cyl, 12 heads, 29 sectors = 143,253,504
Possible Translation:  603 cyl, 16 heads, 29 sectors = 143,253,504
Possible Translation: 1024 cyl, 16 heads, 17 sectors = 142,606,336
Possible Translation:  978 cyl, 11 heads, 26 sectors = 143,210,496

Note: A "custom" or "user-defined" CMOS drivetype  may ask for a
numerical value for the Write Precompensation cylinder and for the
Landing Zone cylinder.  A basic rule-of-thumb for drive models that do
not require the old Write Precomp technique or a Landing Zone because
they are Auto-Parking is to add 1 to the cylinder value being used. As
an example: If cylinders equaled 820, then both Write Precomp and
Landing Zone would be entered as 821. Some BIOS will convert this to
65535 or -1, which are functionally equivalent to "none (not used)".

PHYSICAL/LOGICAL equivalent to NATIVE/TRANSLATION

Already low-level formatted at the factory.

Since a User-definable or Custom translation geometry may be used, it
is imperative that the values be written down and kept with your
permanent records for retrieval in the event of CMOS battery failure.


                          Swift Remote LED Option

               Front View of Drive Without the Plastic Bezel

                                  ΪΔΔΔΒΔΔΔΏ
                                  ³ A ³ B ³    B = Anode
                                  ΓΔΔΔΕΔΔΔ΄    D = Cathode
                                  ³ C ³ D ³
              ...ΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΝΟΝΝΝΟΝΝΝΟΝΝΝΝΝPΝWΝAΝΝΝ...


        ψ Default jumper at C-D for LED mounted on drive PWA
        ψ To use remote LED, remove jumper and extend B (Anode)
          and D (Cathode).
        ψ Swift LED kit 75912397 allows connection to a remote LED
        ψ Swift LED kit 95913369 has an LED for attachment to the
          system front bezel or a 5.25-inch frame kit

Seagate reserves the right to change, without notice, product 
offerings or specifications. (6/26/90)

A copy of this specification file may be obtained by FTP at
ftp://ftp.seagate.com/techsuppt/at/st1162a.txt.